beans diesel

Beans Diesel Performance "No Frills Budget" Fuel Tank Sump

Thoroughbred Sku #: BDP280010
Manufacturer Sku #: 280010


+ Free Ground Shipping

Product Details

Product Name: "No Frills Budget" Fuel Tank Sump
Manufacturer: Beans Diesel Performance
Application: Universal

These are the exact same sumps we sell everyday but they have not been anodized and they are not laser engraved with Beans Diesel on it. They have an aluminum finish.


  • CNC cut 6061 Billet Aircraft Aluminum
  • Stainless Steel hardware
  • Inner "X" ring designed to install without dropping the fuel tank.
  • Viton O-ring impervious to all diesel fuels.
  • Uses all available fuel from the tank. No issues with sucking air when below ¼ tank. Perfect for use with today's high flow lift pump systems. (AirDog, FASS, etc)
  • Single bolt design installs in a snap and less chances for leaks from multiple bolt holes in the tank.
  • Can be installed on any fuel tank with an available 4" diameter flat area.

Fuel Sumps are nothing new these days, you see them everywhere and every company seems to have one. What we have done at BDP is step the tank sump up a notch. Made from 6061 Billet aluminum this little guy is built like a tank and is super simple to install. While still using a no-tank drop design we have made this sump to where it will install with 1 single bolt with one single 3" hole in your tank. This means fewer places to leak and much quicker install. All of our Tank Sumps come with a 3" hole saw, (so no extra trips to the hardware store), and all stainless hardware. The o-ring is made from Viton rubber to ensure it will last the test of time with 0 leaks or decay.

If you are looking to install a FASS fuel system, Air Dog fuel pump or any other aftermarket fuel system you will find through your research that many past and present customers are complaining of noise and Quarter Tank issues. Let's cover the quarter tank issue first. These quarter tank problems are caused by the Draw Straw often supplied with these kits. A draw straw is a tube that is fed through the top of the fuel tank that attaches to the suction line going to your aftermarket fuel system. The draw straw is located wherever you drill the hole, but the only available spots to drill into your factory diesel fuel tank are flexible spots. So as you drive the fuel tank is flexing. When you go around a sharp corner with a quarter tank of fuel, the draw straw can swing away from where gravity takes the fuel. This causes the fuel system to suck air in and acts like your diesel truck is running out of fuel. The truck will die, but once you pull over and the fuel settles, the truck will start again. It's not only annoying, but also dangerous because your power steering stops working when the engine shuts down, brakes also become sketchy.... Noise is another common complaint associated with aftermarket fuel systems. What causes the fuel pump to make so much noise? Strain, the harder the pump has to work, the more noise it is going to make. When the fuel system is trying to suck fuel vertically through a draw straw it's going to cause that fuel pump to work harder. Therefore, more noise is going to be the result. Some of these aftermarket diesel lift pumps utilize the factory draw straw which is very small in diameter. If the fuel system you have purchased is running 1/2" or 5/8" and the factory draw straw is only 5/16" then you have a massive restriction in the fuel flow. This is always going to cause the fuel pump to run harder and louder. The Beans Diesel Fuel Sump is designed to fix all of these issues. By pulling fuel from the bottom of the tank rather than the top, you are taking a lot of strain off the fuel pump, allowing it to operate much quieter and you will never have to worry about quarter tank issues again! Another added bonus to the Beans Diesel Fuel sump is the simple fact that you no longer need to drop the fuel tank to install your aftermarket fuel system. You simply drill a hole in the bottom of the tank, clean out any shavings and install the sump. Minimal tools are required and it shaves about 3 hours off your install time.


There are no reviews for this product yet. Be the first!

Write a Review

Read Review

Spell Check
No videos are available.